Why We Sell Jack Pads to Protect Your Pinch Welds

Why We Sell Jack Pads to Protect Your Pinch Welds

Why We Sell Jack Pads to Protect Your Pinch Welds

If you work on your own car, you have probably done it: slid the jack under the side of the car, found the thin metal seam near the wheel, and lifted. It works, and it feels harmless. But that seam, called the pinch weld, is one of the easiest places on a car to damage, and the damage often shows up months later as rust.

That is why PinchGuard Pads exists. We sell rubber jack pads that fit onto floor jacks and jack stands and protect the pinch weld every time you lift. This post explains what a pinch weld is, what goes wrong when it is lifted bare, and why a simple slotted rubber pad is one of the most useful and least expensive upgrades in a home garage.

What is a pinch weld?

On most unibody cars, the floor and the outer body panels are joined along the bottom edge with a seam of overlapping sheet metal that is spot welded together. That raised metal flange running between the wheels is the pinch weld. Manufacturers often mark the lifting points along it with small notches or arrows, and your owner's manual shows where the lift points are on your car.

The flange is thin sheet metal, and it is coated with paint, seam sealer and undercoating to keep moisture out. It is built to carry a car's weight at the right points, but it is not built to be squeezed, ground against or bent by a hard steel jack saddle.

What happens when you jack on a bare pinch weld

A metal saddle or the flat arm of a jack stand puts a lot of weight on a very small strip of metal. A few things can happen:

·        The flange can bend or fold. Once it is crushed, it no longer sits flat and the next lift is less stable than the last one.

·        The coating can crack or scrape off. Bare steel exposed to road salt and water starts to rust from the inside of the seam, where it is hard to see and hard to repair.

·        Seam sealer can split, which lets water into the joint.

·        The car can shift. A pinch weld that has been bent or that is sitting on a small contact point can let the car move on the stand, which is a safety problem as well as a cosmetic one.

None of this happens in one lift, and that is what makes it easy to miss. It builds up over years of tire rotations, oil changes and brake jobs.

How a slotted jack pad solves the problem

A pinch weld jack pad is a block or puck of rubber with a groove cut across the top. The pinch weld sits in the groove, so the weight rides on the car's body at the flat areas on either side of the seam instead of on the seam itself. The rubber also cushions the contact, keeps metal off metal, and grips better than a bare saddle.

It is a simple idea, and that is the point. A pad costs a small fraction of the repair bill for a rusted or crushed rocker seam, and it takes no extra time to use. You set it on the jack or stand and lift as you always do.

Why we do this

Most people who care about their cars do not mind spending money on parts that make the car faster or better looking. The parts that protect the car do not get the same attention, even though they keep a good car in good condition. We started PinchGuard Pads to give lifting accessories the focus they deserve, and to make a product that does one job well.

We keep the lineup simple. Our pads are made from black rubber, shaped to fit common floor jacks and jack stands, and sold in packs so you have enough for all four corners. We want a customer to be able to pick a pad, put it on, and stop thinking about it.

Who needs jack pads?

Anyone who lifts a car by the side seam can use them, including weekend DIY mechanics, track day and autocross drivers who change wheels and tires often, owners of newer or more valuable cars who want to keep the underside clean, and shops that want to protect customer vehicles.

If you plan to keep a car for a long time, or to sell it someday, a clean, straight pinch weld is a small detail that buyers and inspectors notice.

How to use jack pads safely

A pad protects the car, but it does not make a lift safe on its own. A few habits matter more than any accessory:

·        Check your owner's manual for the factory lift points and use them. Not every car's pinch weld is meant to carry a load along its full length.

·        Work on a hard, level surface. Never lift a car on soft ground, gravel or a slope.

·        Use jack stands before you go under a car or take a wheel off for any length of time. A floor jack is for lifting, not for holding.

·        Make sure the pad matches the weld. Center the seam in the groove, and check that the pad is not cracked, torn or flattened. Replace it if it is.

·        Do not exceed the rating of your jack or stands, and follow the instructions from their manufacturers.

Frequently asked questions

Do jack pads fit every car? Most cars with a pinch weld lifting point can use a slotted pad, but the shape of the weld and the position of the lift points vary. Check your owner's manual and the pad's size before you buy, and contact us if you are not sure.

Can I use a jack pad on a floor jack and on jack stands? Yes. Pads are designed to sit on a floor jack saddle or on the top of a jack stand. Check that the pad sits level and does not slide on the saddle.

Do jack pads wear out? Rubber compresses and can crack over time, especially with heavy use or exposure to oil and sun. Look over your pads each time you use them and replace any that are damaged.

Will a pad let me lift a car anywhere? No. A pad protects the pinch weld, but you should still lift at the points the manufacturer gives for your car.

Protect the parts you can't see

A pinch weld rarely gets noticed until something is wrong with it. A jack pad is a small, inexpensive way to avoid that. If you are ready to protect your car, browse our pinch weld jack pads and pick a set for your garage.